You are here: Tooling

There are four ways to install Tangless inserts, which one suits you depends greatly on the type of application you are installing in and how many inserts you are installing per day.



To install and remove by hand all you need is one of the tools from the mandrel/tool table below, depending on your thread form and diameter:
Each Part number includes mandrel and handle.
mandrel tool
Metric Mandrel/Tool Table Inch Mandrel/Tool Table
Installation Removal
Free Running 2CT10-M2.5F 2CT30-M2.5F
M2.5 x 0.45 Locking 2CT10-M2.5L 2CT30-M2.5L
Replacement Pawl 2CT20-M2.5 2CT40-M2.5
Free Running 2CT10-M3F 2CT30-M3F
M3 x 0.5 Locking 2CT10-M3L 2CT30-M3L
Replacement Pawl 2CT20-M3 2CT40-M3
Free Running 2CT10-M4F 2CT30-M4F
M4 x 0.7 Locking 2CT10-M4L 2CT30-M4L
Replacement Pawl 2CT20-M4 2CT40-M4
Free Running 2CT10-M5F 2CT30-M5F
M5 x 0.8 Locking 2CT10-M5L 2CT30-M5L
Replacement Pawl 2CT20-M5 2CT40-M5
Free Running 2CT10-M6F 2CT30-M6F
M6 x 1 Locking 2CT10-M6L 2CT30-M6L
Replacement Pawl 2CT20-M6 2CT40-M6
Free Running 2CT10-M8F 2CT30-M8F
M8 x 1.25 Locking 2CT10-M8L 2CT30-M8L
Replacement Pawl 2CT20-M8 2CT40-M8
Free Running 2CT10-M10F 2CT30-M10F
M10 x 1.5 Locking 2CT10-M10L 2CT30-M10L
Replacement Pawl 2CT20-M10 2CT40-M10
Free Running 2CT10-M12F 2CT30-M12F
M12 x 1.75 Locking 2CT10-M12L 2CT30-M12L
Replacement Pawl 2CT20-M12 2CT40-M12
  Installation Removal
UNC 2-56 Free Running & Locking 2KREC-02 2KRTC-02
Replacement Pawl 2KIPC-02K 2KRPC-02K
 
UNC 4-40 Free Running & Locking 2KREC-04 2KRTC-04
Replacement Pawl 2KIPC-04K 2KRPC-04K
 
UNC 6-32 Free Running & Locking 2KREC-06 2KRTC-06
Replacement Pawl 2KIPC-06K 2KRPC-06K
 
UNC 8-32 Free Running & Locking 2KREC-2 2KRTC-2
Replacement Pawl 2KIPC-2K 2KRPC-2K
 
UNC 10-24 Free Running & Locking 2KREC-3 2KRTC-3
Replacement Pawl 2KIPC-3K 2KRPC-3K
 
UNC 1/4-20 Free Running & Locking 2KREC-4 2KRTC-4
Replacement Pawl 2KIPC-4K 2KRPC-4K
 
UNF 10-32 Free Running & Locking 2KREF-3 2KRTF-3
Replacement Pawl 2KRTF-3 2KRPF-3K
 
Ideal for installing inserts in small production runs or in areas where compressed air or electricity are not available and offers a quicker alternative to the simple hand installation tool. The tool is suitable for use when installing free running and locking inserts. mandrel tool
Metric Mandrel/Tool Table Inch Mandrel/Tool Table
Installation
M2.5 x 0.45 Free Running & Locking 2KPHM-2.5
Replacement Pawl 2KPIM-2.5
M3 x 0.5 Free Running & Locking 2KPHM-3
Replacement Pawl 2KPIM-3
M4 x 0.7 Free Running & Locking 2KPHM-4
Replacement Pawl 2KPIM-4
M5 x 0.8 Free Running & Locking 2KPHM-5
Replacement Pawl 2KPIM-5
M6 x 1 Free Running & Locking 2KPHM-6
Replacement Pawl 2KPIM-6
M8 x 1.25 Free Running & Locking 2KPHM-8
Replacement Pawl 2KPIM-8
M10 x 1.5 Free Running & Locking 2KPHM-10
Replacement Pawl 2KPIM-10
M12 x 1.75 Free Running & Locking 2KPHM-12
Replacement Pawl 2KPIM-12
  Installation
UNC 2-56 Free Running & Locking 2KPHC-02
Replacement Pawl 2KIPC-02K
UNC 4-40 Free Running & Locking 2KPHC-04
Replacement Pawl 2KIPC-04K
UNC 6-32 Free Running & Locking 2KPHC-06
Replacement Pawl 2KIPC-06K
UNC 8-32 Free Running & Locking 2KPHC-2
Replacement Pawl 2KIPC-2K
UNC 10-24 Free Running & Locking 2KPHC-3
Replacement Pawl 2KIPC-3K
UNF 10-32 Free Running & Locking 2KPHF-3
Replacement Pawl 2KIPF-3K
UNC 1/4-20 Free Running & Locking 2KPHC-4
Replacement Pawl 2KIPC-4K
UNF 1/4-28 Free Running & Locking 2KPHF-4
Replacement Pawl 2KIPF-4K

Recoil electric powered installation tooling uses a small generator to install fasteners at a much higher rate than a manual installation tool or pre-winder tool. This tool is ideal for installation of medium to large quantities of inserts. To install using electric tooling all you need is:

Transformer: SBT50-230-UK
Electric Tool: HIOS KFS-12
Pre-Winder Adaptor (required for FEA use only): CT5408-PA

Then:

A Mandrel: Choose from the mandrel/tool table below depending on your thread form and diameter
OR:
A Front End Assembly: from the Electric Front End Assembly table below depending on your thread form and diameter

mandrel tool
Metric Mandrel/Tool Table Inch Mandrel/Tool Table
Installation Removal
Free Running 2CT10-M2.5F 2CT30-M2.5F
M2.5 x 0.45 Locking 2CT10-M2.5L 2CT30-M2.5L
Replacement Pawl 2CT20-M2.5 2CT40-M2.5
Front End Assembly 2KPEM-2.5
Free Running 2CT10-M3F 2CT30-M3F
M3 x 0.5 Locking 2CT10-M3L 2CT30-M3L
Replacement Pawl 2CT30-M3L 2CT40-M3
Front End Assembly 2KPEM-3
Free Running 2CT10-M4F 2CT30-M4F
M4 x 0.7 Locking 2CT10-M4L 2CT30-M4L
Replacement Pawl 2CT20-M4 2CT40-M4
Front End Assembly 2KPEM-4
Free Running 2CT10-M5F 2CT30-M5F
M5 x 0.8 Locking 2CT10-M5L 2CT30-M5L
Replacement Pawl 2CT20-M5 2CT40-M5
Front End Assembly 2KPEM-5
Free Running 2CT10-M6F 2CT30-M6F
M6 x 1 Locking 2CT10-M6L 2CT30-M6L
Replacement Pawl 2CT30-M6L 2CT40-M6
Front End Assembly 2KPEM-6
Free Running 2CT10-M8F 2CT30-M8F
M8 x 1.25 Locking 2CT10-M8L 2CT30-M8L
Replacement Pawl 2CT20-M8 2CT40-M8
Free Running 2CT10-M10F 2CT30-M10F
M10 x 1.5 Locking 2CT10-M10L 2CT30-M10L
Replacement Pawl 2CT20-M10 2CT40-M10
Free Running 2CT10-M12F 2CT30-M12F
M12 x 1.75 Locking 2CT10-M12L 2CT30-M12L
Replacement Pawl 2CT20-M12 2CT40-M12
  Installation Removal
Free Running & Locking 2KREC-02 2KRTC-02
UNC 2-56 Replacement Pawl 2KIPC-02K 2KRPC-02K
Front End Assembly 2KPEC-02
 
Free Running & Locking 2KREC-04 2KRTC-04
UNC 4-40 Replacement Pawl 2KIPC-04K 2KRPC-04K
Front End Assembly 2KPEC-04
 
Free Running & Locking 2KREC-06 2KRTC-06
UNC 6-32 Replacement Pawl 2KIPC-06K 2KRPC-06K
Front End Assembly 2KPEC-06
 
Free Running & Locking 2KREC-08 2KRTC-08
UNC 8-32 Replacement Pawl 2KIPC-08K 2KRPC-08K
Front End Assembly 2KPEC-2
 
Free Running & Locking 2KREC-10 2KRTC-10
UNC 10-24 Replacement Pawl 2KIPC-10K 2KRPC-10K
Front End Assembly 2KPEC-3
 
Free Running & Locking 2KREC-4 2KRTC-4
UNF 1/4-20 Replacement Pawl 2KIPC-4K 2KRPC-4K
Front End Assembly 2KPEC-4
Free Running & Locking 2KREF-3 2KRTF-3
UNC 0-32 Replacement Pawl 2KIPF-3K 2KRPF-3K
Front End Assembly 2KPEF-3
 
UNF 1/4-28 Front End Assembly 2KPEF-4
 

Recoil pneumatic powered installation tooling uses standard air supply to install fasteners at a much higher rate than a manual installation tool or prewinder tool. This tool is ideal for installation of medium to large quantities of inserts, especially when used in combination with Stripfeed.
To install using air tooling all you need is:

Air Motor and Adapter: NR-HL 1409 (M2.5 to M6, (2-56 to 1/4") or NR-HL 1410 (M8 to M12)

Front End Assembly: Choose from the table below depending on your thread form and diameter

mandrel tool
Metric Mandrel/Tool Table Inch Mandrel/Tool Table
Installation
M2.5 x 0.45 2KPAM-2.5
M3 x 0.5 2KPAM-3
M4 x 0.7 2KPAM-4
M5 x 0.8 2KPAM-5
M6 x 1 2KPAM-6
M8 x 1.25 2KPAM-8
M10 x 1.5 2KPAM-10
M12 x 1.75 2KPAM-12
Installation
UNC 2-56 2KPAC-02
UNC 4-40 2KPAC-04
UNC 6-32 2KPAC-06
UNC 8-32 2KPAC-2
UNC 10-24 2KPAC-3
UNC 1/4-20 2KPAC-4
UNF 10-32 2KPAC-3
UNF 1/4-28 2KPAF-4